last Update:
19/9/2024Selector
Download our new leaflet here
ANAEROBIC CURE THREADLOCK AND RETAINER PRODUCTS SELECTION TABLE / CHART
Thread lock selector chart
StarLoc Anaerobic are single part threadlock products for locking all threaded parts against vibration loosening and fatigue / wear plus the added advantages of stopping leakage of fluids and gasses past the threads as well as preventing any build up of corrosion between the two threaded parts.
More reliable than traditional methods,
Easier to use,
Lower cost due to reduced parts,
Threadlockers are 100% reliable unlike other methods of locking ( lock washers, split pins, nylon insert nuts etc... ) and because you can cut down on parts you can lower the costs of an item.
Starloc threadlockers cure after contact with metals and the absence of air, many other brands of threadlockers wont cure on plated metals or stainless steel etc, Starlocs unique formulations will cure fully even on stainless steel or chrome plate.
If working in cold conditions, with dirty parts or when a high speed cure is required a range of spray on cleaner/primers and accelerators are available to speed cure ( see below )
| STARLOC GRADE |
EQUV. LOCTITE GRADE |
COLOR | VISCOSITY CPS |
GAP FILL mm |
MAX TEMP | SHEAR STRENGTH N/mm2 |
BREAKAWAY TORQUE Nm |
PREVAILING TORQUE Nm |
CURE TIME MINUTES |
NAME | MAIN USES |
| 9-222 | 222 | PURPLE | 1000 | .5 | 160C | 2-3.5 | 4-8 | 2-4 | 15 | SCREW LOC | LOW STRENGTH:EASY DISASSEMBLY:SMALL FASTENERS |
| 9-242 | 242 | BLUE | 1000 | .1 | 160C | 12 | 17-22 | 5-8 | 3-7 | NUT LOC | MED. STRENGTH GENERAL PURPOSE |
| 9-243 | 243 | BLUE | 1200 | .1 | 160C | 12 | 17-22 | 5-8 | 10 | BOLT LOC | OIL TOLERANT, FOR AS RECEIVED PARTS |
| 9-260 | 260 | RED | 1300 | .25 | 160C | 17 | 28-32 | 50-58 | 10 | STUD LOC | HIGH STRENGTH, CAN BE DISASSEMBLED UP TO 6mm |
| 9-262 | 262 | RED | 2500 | .25 | 160C | 19 | 30-35 | 55-65 | 15 | STUD LOC+ | EXTRA STRENGTH STUD LOCK 6mm TO 12 mm |
| 9-270 | 270 | RED | 500 | .25 | 160C | 21 | 32-40 | 60-70 | 10 | STUD LOC++ | FOR FASTENINGS UP TO 25mm FOR NO DISASSEMBLY |
| 9-272 | 272 | RED | 600 | .25 | 160C | 22 | 35-55 | 55-75 | 10 | STUD LOC+++ | EXTRA STRENGTH FOR 25mm+ STUDS |
| 9-277 | 277 | RED | 7000 | .25 | 160C | 25 | 35-55 | 55-75 | 10 | STUD LOC MAX | PERMANENT GRADE STUD LOC FOR V.BIG STUDS |
| 9-290 | 290 | GREEN | 15 | .05 | 160 C | 16 | 17-22 | 5-8 | 5-10 | PENETRATING STUD LOC |
MEDIUM STRENGTH, WICKING GRADE FOR POST APPLICATION |
| 9-292 | 292 | YELLOW | 15 | .05 | 160C | 19 | 28-32 | 50-58 | 5-10 | PENETRATING THREAD LOC |
HIGH STRENGTH, WICKING GRADE THREAD LOCK FOR POST APPLICATION |
| 9-022 | PINK | 10-20 | .1 | 160C | 2-4 | 1-3 | SCREW LOCK | LOW STRENGTH THREADLOC FOR USE ON PLASTIC / GLASS / METAL / WOOD PARTS |
|||
| 9-024 | CLEAR | 10-20 | .1 | 160C | 15 | 1-3 | NUT LOCK | MEDIUM STRENGTH THREADLOC FOR USE ON PLASTIC / WOOD / GLASS / METAL PARTS | |||
| 9-077 | BLACK | 10-20 | .1 | 160C | 25 | 1-3 | STUD LOCK | HIGH STRENGTH THREADLOC FOR USE ON PLASTIC / METAL / GLASS / WOOD PARTS |
Retainer / Bearing Shaft grades selector chart
Single part retainer products for bonding, locking and sealing turned parts, shafts, bearings ( non threaded parts ) , suitable for use on new parts, worn parts, against vibration loosening, vibration fatigue and stress cracking plus the added advantages of stopping leakage of fluids and gasses past as well as preventing any build up of corrosion between the parts.
Retainers are 100% reliable, giving 100% surface contact that is unobtainable with other methods of fitting bearings and shafts etc, press fitting generally gives around 20% to 50 % surface contact, bearing fit gives a totally reliable 100% surface contact that wont leak or work loose over time.
More reliable than traditional methods,
Easier to use, no heating parts before assembly
Lower cost due to faster machining,
tolerances can be relaxed to obtain faster assembly and less rejected parts.
Starloc retainers cure after contact with metals and the absence of air, many other brands of retainer wont cure on plated metals or stainless steel etc, Starlocs unique formulations will cure fully even on stainless steel or chrome plate
If working in cold conditions, with dirty parts or when a high speed cure is required a range of spray on cleaner/primers and accelerators are available to speed cure ( see below )
| STAR-LOC GRADE |
EQU. LOCTITE GRADE |
COLOR | VISCOSITY cPS |
GAP FILL mm |
CURED STRENGTH N/mm2 |
SHEAR STRENGTH BREAKAWAY Nm |
SHEAR STRENGTH PREVAILING Nm |
CURE TIME MINUTES |
MAX TEMP (DEG C) |
NAME | USE |
| 9-601 | 601 | GREEN | 150 | ..15 | 20 | 30-35 | 55-70 | 10-15 | 160 | GP. RETAINER | CLOSE FIT PARTS, ROLER BEARINGS, CAMS ETC |
| 9-603 | 603 | GREEN | 125 | .05 | 20 | 30-35 | 55-70 | 10-15 | 160 | GP. RETAINER | AS 601, NO PRE CLEANING REQUIRED |
| 9-609 | 609 | GREEN | 125 | .05 | 20 | 30-35 | 55-70 | 30-60 | 160 | SLOW CURE GP | SLOW CURE VERSION OF 603 |
| 9-620 | 620 | YELLOW | 1500 | .15 | 25 | 30-40 | 55-70 | 10-15 | 280 | HIGH STRENGTH HIGH TEMP FAST CURE |
UP TO 450 DEG F HIGH TEMP |
| 9-635 | 635 | GREEN | 2500 | .15 | 30 | 30-40 | 55-75 | 10 | 160 | MAX STRENGTH FAST CURE | FOR BUSHES,KEYS,SPLINES,TUBING WITH CLOSE FIT |
| 9-638 | 638 | GREEN | 2500 | .15 | 30 | 30-40 | 55-75 | 40 | 160 | MAX STRENGTH SLOW CURE | AS 635, BUT SLOW CURE |
| 9-641 | 641 | YELLOW | 1500 | .2 | 11.5 | 12-15 | 16-22 | 15 | 160 | CONTROLLED STRENGTH RETAINER |
BEARINGS, SHAFTS,REDUCES FRETTING |
| 9-6-48 | 648 | YELLOW | 1500 | .2 | 25 | 30-35 | 55-70 | 3-5 | 180 | HIGH STRENGTH, FAST CURE |
UPTO 180 DEG C, ELECTRIC MOTORS,PULLEYS,BEARINGS ETC |
| 9-660 | 660 | RED | 3000 | .3 | 25 | 30-40 | 55-70 | 60+ | 160 | EXTRA GAP FILL | WORN SHAFTS,PULLEYS ETC |
ACCELERATOR / PRIMER ( spray on )
TO SPEED CURE OF THREAD LOCKERS AND RETAINERS
SIMPLY APPLY THIS PRODUCT TO ONE SURFACE BEFORE ASSEMBLY TO SPEED CURE ON CLEAN PARTS, USE DEGREASER / PRIMER TO CLEAN AND PRIME DIRTY PARTS
| CODE | TYPE | DESCRIPTION |
| ANP N /50 | Primer / activator for threadlock / retainer / gasket sealer solvent based |
|
| ANP N/150 | "" | AS ABOVE, LARGER SIZE |
| ANP `T`/50 | Primer / activator for threadlock / retainer / gasket sealer solvent free |
|
| ANP T/150 | "" | AS ABOVE, LARGER SIZE |
| DEG / 50 | DEGREASER / PRIMER | FOR CLEANING PARTS PRIOR TO ASSEMBLY |
| DEG / 150 | DEGREASER / PRIMER | FOR CLEANING PARTS PRIOR TO ASSEMBLY |
